SX-WF-3800 橡膠過冰水、過水粉槽
外型尺寸：（L*W*H）3800*950*1430（mm）
另可選型號尺寸（具體價格請來電咨詢）：
| 型號 | 長 | 寬 | 高mm |
| SX-WF-2895 | 2800 | 950 | 1430 |
| SX-WF-3095 | 3000 | 950 | 1430 |
| SX-WF-3819 | 3800 | 1900 | 1430 |
| SX-WF-2819 | 2800 | 1900 | 1430 |
| SX-WF-3019 | 3000 | 1900 | 1430 |
| SX-WF-XX | 客戶定 | 客戶定 | 1430 |
標準配備冰水機：10匹。
另可選：15匹，20匹，30匹，40匹，80匹等。
用途：本機適用于橡膠出片冷卻定型。
特點：本機采用冷凍水冷卻后，再經過添加防粘ANTITACK161幫助捏合出片之胚料，防止未硫化胚料加沾疊而避免死膠的產生。
使用說明：
1.進料膠片厚薄要一致且平整進入膠輥，
太薄的膠片進膠輥必需折成雙層，噴水量要夠多，
彈簧（進料膠輥）不要調整過緊，工人的操作速度快，以免卷料。
2.以上操作失誤，如有卷料，清理時，刀片一定不要損傷膠輥。
3.號碼三組膠輥進料時，薄料必需折成雙層稍微一點拉力。
不致于卷料，仍有存在阻料。查彈簧是否調整不當，
查膠輥是否卡住，上面膠輥和下面膠輥是否緊貼，軸承是否沒換油卡死，鏈條是否過松等。
4.壓水不干，煉膠機上要裝齊邊刀，減少碎料，平整一致，調整膠輥彈簧，注意彈簧不要調死，以免損壞電機。
Purpose：This machine is used to making the rubber setted out cooling .
Specialty：The rubber going through this machine for cooling ,ane then add the anti-adhesive ANTITACK161for heiping knead the rubber ,avoid the material not yet vnvulcanized overlap to avert produce the bad rubber .
INSTRUCTIONS:
1.The thickness fed rubber slices must be consistent and the rubber slices should enter in a lever . Too thin rubber slices should enter in a way of double-decker .Water them with enough volume;do not adjust the spring too tight.The operating speed must be fast enough to avoid material rolling.
2.If above operational errors occur and material rolled,don’t let the blade operate the rubber roller when cleaning up.
3.When the triple-rubber-roller is feeding material, thin one must be folded into double-decker. If there still exist non-smoothly feeding,checkwhether the spring is adjusted properly;or check whether the rubber roller is blocked;check whether the upper rubber roller is stuck with the lower one ; or check whether the bearing roller is blockede for without oil replacing ;or check whether the chain is too loose,etc.
4.Pressurized water quit ,the knives should be installed in a level to the rubber making machine . Reduce rubber oddments and make rubber in a level and in the same thickness. Do adjust the spring, but not too tight to avoid damaging the MORTOR.
